EZYPATTERNDXF pattern tools
Runs in your browser
Pattern notes

How to make a garment marker for free — marker length and yardage from a DXF, no CAD license

Markers are usually made in paid pattern CAD such as Gerber AccuMark, Lectra or Optitex. When you only need sample yardage or a quote for a small order, a DXF file is enough: you can build the marker for free in your browser.

Updated 2026-11-21Reading time 6 min

What a marker is

A marker is the layout of all pattern pieces to be cut, placed inside the fabric width without overlapping. The shorter the marker, the less fabric you use. A marker gives you three numbers:

  • Marker length: the fabric length the layout takes
  • Efficiency: the share of the marker area covered by pattern pieces (%)
  • Consumption per garment: marker length ÷ number of garments in the marker

Commercial CAD marker vs a free web tool

Pick by what you need to do. These are the usual differences.

Commercial pattern CADEZYPATTERN Marker Nesting
CostPaid licenseFree
InstallDesktop softwareNothing to install — runs in the browser
FilesOwn format · DXFAAMA / ASTM DXF (the format most CAD systems export)
Auto nestingYesYes — fabric width, size quantities, direction (1WAY · 2WAY), piece gap
Stripe matchingYesOne-direction stripe matching · plaid (both directions) not yet
ShrinkageYesWidth and length % per fabric
OutputPlotter / cutter outputPNG · SVG image and marker DXF (no plotter file yet)
File privacyOn your PCNot uploaded — computed inside your browser

In short: a free tool is enough for sample yardage, quotes and fabric order quantities. If you need plotter output in the cutting room, plaid matching or a link to factory cutting systems, a commercial CAD is the right choice.

What you need

  • A DXF pattern exported from your pattern CAD as AAMA or ASTM DXF. Several graded sizes in one file are fine. No file yet? Try the sample shirt DXF.
  • Fabric width: the usable width, not the full width (leave out selvedges and pin marks).
  • Quantities per size to put in the marker (e.g. S 1 · M 2 · L 1).
  • Shrinkage after washing or steaming, in %, if you know it. Otherwise 0.

Steps

  1. Open Marker Nesting and drop your DXF in.
  2. Create a fabric (e.g. shell 62") and put each pattern card on it. Pieces in another fabric, such as lining or rib, get their own fabric.
  3. In the fabric settings, set width, shrinkage, direction (1WAY / 2WAY) and run time.
  4. Enter the quantity per size.
  5. Press Start. You watch the layout improve live; when it finishes, each fabric shows marker length, efficiency and consumption per garment.
  6. Save the result as a PNG · SVG image or a marker DXF, and save the job file to continue later.

Step-by-step screenshots are in the Marker Nesting user guide.

Reading the result

  • Low efficiency (say below 70%)? Check the piece gap, direction limits and run time. If the fabric allows 2WAY, efficiency goes up.
  • Consumption per garment changes with the size ratio. Build the marker with the real order ratio, or the order quantity will be off.
  • Order quantity = consumption per garment × quantity × (1 + loss %). A worked example is in How to calculate fabric consumption per garment.

FAQ

Is it really free?

Yes. Free, no sign-up.

Are my pattern files uploaded?

No. The DXF is read and computed inside your browser only. Nothing is sent to a server.

Which CAD systems work?

It reads AAMA / ASTM DXF, which most pattern CAD systems export. Inch files without a unit header are detected by size and read as inches.

Can I take the marker back into CAD?

You can save the marker as DXF. Plotter files (PLT etc.) are not available yet.

Ask a question

Questions about this note or the tools, or a topic you would like covered? Send it in. Good questions go into the FAQ of the next note.