EZYPATTERNDXF pattern tools
Runs in your browser
Pattern notes

How to calculate fabric consumption per garment — marker length, efficiency, loss and shrinkage

Fabric consumption is the fabric length one garment needs. The most accurate way is to build a marker and measure it; without a marker you can estimate from pattern area. Both methods and the order quantity, with real numbers.

Updated 2026-11-21Reading time 7 min

1. From a marker (most accurate)

Consumption per garment = marker length ÷ garments in the markerIf the marker mixes sizes, this is the average for that size ratio.

Example: usable width 152.4 cm (60"), a marker with 4 T-shirts (S 1 · M 2 · L 1) is 3.80 m long:

3.80 m ÷ 4 = 0.95 m per garmentIn yards: 0.95 ÷ 0.9144 = 1.04 yd per garment

2. Check the efficiency

Efficiency = total pattern area in the marker ÷ (marker length × usable width)

If one garment's pieces cover 1.15 m², four garments cover 4.60 m²:

4.60 ÷ (3.80 × 1.524) = 79.4 %

Knit tops usually land around 75–85%; large, simple pieces go higher. If it is very low, the usual causes are direction limits (1WAY), the piece gap or the fabric width.

3. Quick estimate without a marker

When you only need a number fast, for a quote, estimate from pattern area:

Consumption ≈ pattern area per garment ÷ (usable width × expected efficiency)
1.15 m² ÷ (1.524 m × 0.80) = about 0.94 m per garment

The result moves a lot with the efficiency you assume, so check it with a real marker once the order is confirmed.

4. Add shrinkage

Fabric shrinks after washing or steaming, so the cutting pattern has to be larger for the finished size to come out right.

Cut length = finished length ÷ (1 − shrinkage)4% lengthwise: ÷ 0.96 ≈ ×1.042

If the example marker grows 4% lengthwise: 3.80 ÷ 0.96 = about 3.96 m, or about 0.99 m per garment. Width shrinkage fits fewer pieces across the width and can raise consumption further. In Marker Nesting, enter width and length shrinkage per fabric and it is applied when nesting.

5. Order quantity

Order quantity = consumption per garment × quantity × (1 + loss %)Loss: marker ends, fabric defects and shade, spreading waste

For 500 garments with 3% loss:

0.95 m × 500 × 1.03 = 489.25 m → about 490 m (about 536 yd)
ItemValue
Marker length (4 garments)3.80 m
Consumption per garment0.95 m · 1.04 yd
Efficiency79.4 %
With 4% lengthwise shrinkageabout 0.99 m per garment
Order (500 pcs · 3% loss, before shrinkage)about 490 m

Common mistakes

  • Using the full fabric width: use the usable width without selvedges and pin marks.
  • One sample size for the whole order: orders heavy on large sizes use more fabric. Build the marker with the real size ratio.
  • Forgetting shrinkage: a few percent of lengthwise shrinkage on knits makes a big difference to the order.
  • Mixing units: 1 yd = 0.9144 m, 1" = 2.54 cm. Many mills quote width in inches and consumption in yards.

FAQ

What efficiency is good?

It depends on the product, fabric width and direction limits. Knit tops are often around 75–85%; stripe matching and 1WAY fabrics come out lower.

What if I cannot make a marker myself?

If you have a DXF pattern, Marker Nesting builds an automatic marker for free and gives the consumption. Without a pattern, Pattern Draft can draw a sample pattern from your spec and send it over.

Ask a question

Questions about this note or the tools, or a topic you would like covered? Send it in. Good questions go into the FAQ of the next note.